All articles

Evotech RC Frame Sliders for the 2025 Aprilia Tuono V4 Factory 1100

Evotech RC’s Italian-made frame sliders are well finished, with slim aluminum brackets that follow the lines of the Tuono V4 Factory’s frame.

I liked the way the Top Block Racing frame sliders looked on my Tuono, but at almost a kilogram each, their weight had bothered me from the start. Just over a year after writing about them, I finally looked for a lighter replacement. Of the kits I found online, the Evotech RC STDA-007 was the only other one whose design appealed to me.

When Evotech RC told me its kit was lighter, I decided to give it a try. I planned to buy and review it anyway, so I asked for a discount in exchange for the review, and they agreed.

The kit arrived neatly packed, and Evotech RC backs it with a five-year warranty.

Evotech RC’s gray frame slider box with red sides and the STDA-007 label

After unpacking the kit, I weighed the complete set. It came in at around 970 g, about half the weight of the TBR pair.

Both kits use brackets that attach to two engine mounting points on each side. TBR uses broad, angular pads and substantially larger brackets, with rubber dampers between the brackets and the slider bodies. Evotech RC pairs four-sided heads with slim aluminum brackets that tuck neatly under the frame. The machining and finish impressed me on both kits, and I like how each looks on the Tuono. I’d have a hard time choosing between them on looks alone.

Weight was the deciding factor for me. Saving roughly a kilogram suits the sporting character of my 2025 Aprilia Tuono V4 Factory 1100, so I fitted the Evotech RC kit.

Sliders and mounting hardware

The two sliders come with an aluminum bracket for each side, four engine-mount bolts, inner and outer spacer blocks, and eight M4 slotted cone-point set screws. Evotech RC also includes a sheet of decals and sells optional aluminum tie-down eyelets separately in black or silver for securing the bike during transport.

Complete Evotech RC kit laid out with both sliders, V4 brackets, spacers and bolts

In the close-up, the gold-colored insert on my set stands out against the black slider head. On the bike, I like how the inserts echo the gold finish of the front fork in the Öhlins Smart EC 2.0 suspension package. The other insert colors are black, blue, green, orange, red, silver, and titanium.

Two assembled Evotech RC sliders showing the gold insert on one and the threaded end of the other

The insert threads into the slider body, with a serrated washer between the insert and the head.

Disassembled Evotech RC slider with its polymer head, threaded body, bolt, gold insert and washer

Fitment on the 2025 Tuono V4 Factory

Some of the installation photos are darker than I’d have liked. My Tuono was already in winter storage, so I took them in the garage.

Fitting the Evotech RC kit was straightforward. The mounting points on the naked Tuono are easy to reach with the bodywork in place. I worked one side at a time, starting on the left, so one side of the engine stayed bolted in place throughout the job.

The one detail to watch is the spacers between the frame and the engine. They can drop out as you remove the engine-mount bolts, especially on the right side, where they’re easy to lose.

Two exposed engine mounting points on the right side of the Aprilia Tuono before the bracket goes on

I tightened the engine-mount bolts to 50 Nm with a torque wrench and an 8 mm hex bit, in line with the figure Evotech RC lists for the frame bolts.

Right-side Evotech RC bracket bolted in place with the threaded slider mounting hole exposed

With each head’s fastener still loose, I held the head by hand at the angle I wanted and tightened its mount with an 8 mm hex bit. I then secured the head with a 10 mm hex bit. Both heads stayed in position, and I left out the M4 slotted cone-point set screws supplied with the kit.

Gold threaded insert and washer on a 10 mm hex bit beside the right slider head

Finished right-side frame slider with its gold insert seated inside the four-sided head

The overhead close-up shows the right-hand bracket beside the frame, where I measured just over 6 mm of clearance.

Side profile of the installed right slider showing how its head projects from the bracket

With the left slider head off, you can see how the body projects from the bracket. Once assembled, the bracket follows the frame closely, with about 5 mm of clearance that gives it some room to deform under impact.

Left-side bracket with the threaded slider body installed before the head goes on

Full left-side view of the 2025 Aprilia Tuono V4 Factory 1100 with the Evotech RC slider installed

With both heads fitted, the view over the tank gives a better sense of how far they sit out from the bike.

View over the Tuono’s fuel tank showing both Evotech RC sliders extending from the sides

Final thoughts

From the saddle, the sliders are unobtrusive, and from the side, the gold inserts look like they belong on the bike. They’re staying on my Tuono, and I’d happily recommend them, especially if keeping weight down matters to you.

Search the archive

Type at least two characters.